Tennessee TDOSHS CDL General Knowledge Practice Test 5
Test 5 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Tennessee test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age21 years
-
1. You are hauling an open box of loose gravel. What does that load require?
Show answer
Answer A: A cover, so that material cannot blow off or spill onto the road
Loose material that can be blown or spilled has to be covered so it does not come out of the body and strike traffic behind.
-
2. The temperature is around freezing and the road looks wet. What is a practical way to tell whether it is icy?
Show answer
Answer C: Check for ice building up on the mirrors, antenna or the front of the vehicle
Ice that forms on the mirror, antenna or windshield is a warning that the road surface is freezing too, and black ice can look like a wet road.
-
3. As a long vehicle goes around a corner, how do the rear wheels travel compared with the front wheels?
Show answer
Answer A: They follow a tighter path, closer to the inside of the turn
The rear wheels off-track toward the inside of the turn, and the longer the vehicle the bigger the difference, which is why the front must swing wide enough to keep the rear off the curb.
-
4. A driver hauling a sealed trailer that cannot be opened is still responsible for what?
Show answer
Answer D: Making sure the rig is not over the gross or axle weight limits
A seal prevents inspecting the contents, but the driver must still confirm the vehicle is not overloaded.
-
5. Before raising the hood to inspect the engine compartment, what should you do?
Show answer
Answer B: Shut off the engine, set the parking brake and chock the wheels if needed
The engine compartment is inspected with the engine off and the vehicle secured so nothing can move or turn while your hands are inside.
-
6. You must steer hard around an obstacle at highway speed. What is the correct technique?
Show answer
Answer B: Avoid braking while turning, turn only as far as needed, and countersteer as soon as the obstacle is passed
Braking during a hard steering input can lock the wheels and start a skid, and turning back at once keeps the vehicle from running off the far side of the road.
-
7. Why does the commercial driver manual tell you to look far down the road instead of only at the vehicle ahead?
Show answer
Answer D: So you can adjust smoothly instead of braking hard at the last moment
A heavy vehicle cannot react quickly, so early information lets you slow gradually rather than make a sudden stop or swerve.
-
8. On a two lane road carrying traffic in both directions, where do the three warning devices go?
Show answer
Answer C: About 10 feet from the vehicle on the traffic side, 100 feet behind and 100 feet ahead
Traffic can approach from either direction, so one device goes close to the vehicle and one is placed about 100 feet away in each direction.
-
9. Which wheel or rim condition must be treated as a defect during the walkaround?
Show answer
Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts
Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.
-
10. What does the driver check in the final step of the seven-step inspection?
Show answer
Answer A: Hydraulic brake leaks where those brakes are fitted, then the parking brake and the service brakes
The last step is done with the engine started: test for hydraulic leaks on vehicles with hydraulic brakes, then prove that the parking brake holds and that the service brakes stop the vehicle.
-
11. On the Interstate System, what are the federal maximums for a tandem axle group and for gross vehicle weight?
Show answer
Answer B: 34,000 pounds and 80,000 pounds
The federal Interstate limits allow 34,000 pounds on a tandem axle group and 80,000 pounds gross.
-
12. What are you checking when you look at the batteries during the engine compartment inspection?
Show answer
Answer D: That they are securely mounted, the connections are tight and free of corrosion, and the caps are in place
Loose or corroded batteries can fail or short out, so the mount, cables, terminals and vent caps are all part of the check.
-
13. On a set of dual tires, which condition must be reported as a defect?
Show answer
Answer D: The two tires are touching each other or rubbing on part of the vehicle
Duals that touch each other or the vehicle overheat and wear quickly, so they must be separated by proper spacing and inflation before driving.
-
14. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?
Show answer
Answer B: That the seal number matches the paperwork and that the doors are properly closed
You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.
-
15. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
16. Why is cargo often covered with a tarp?
Show answer
Answer C: To protect people from spilled cargo and to protect the cargo from weather
A cover keeps material from blowing or spilling onto the road and shields the load from rain and sun; it does not replace securement.
-
17. Why should the mirrors be checked repeatedly while you make a tight turn?
Show answer
Answer C: To watch the rear of the vehicle clear other vehicles and objects
In a long vehicle the rear wheels cut inside the path of the front wheels, so only the mirrors show whether the rear is clearing curbs, poles and other vehicles.
-
18. Your vehicle begins to hydroplane on a wet road. What should you do?
Show answer
Answer B: Release the accelerator and push in the clutch so the wheels can turn freely and regain grip
Hydroplaning tires are riding on water; slowing without braking lets them settle back onto the road and grip again.
-
19. Which brake lining condition must be reported?
Show answer
Answer C: Linings that are worn thin, loose, cracked or soaked with oil or grease
Linings must have enough material left and must be securely attached and clean, because a thin, loose or contaminated lining cannot deliver its share of braking.
-
20. Where is a dunnage bag used and how does it work?
Show answer
Answer D: Between pieces of cargo inside a van, where it is inflated to take up the gap
A dunnage bag is placed in the void between loads and inflated so the cargo is wedged and cannot move as the vehicle rolls and brakes.
-
21. Apart from the legal duty, what is the main practical reason for a thorough pre-trip inspection?
Show answer
Answer A: It finds problems that could cause a breakdown or a crash before the vehicle is on the road
A defect found in the yard is an inconvenience, while the same defect found at highway speed can be a crash, so the inspection is where problems are cheapest to fix.
-
22. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?
Show answer
Answer B: Warn other traffic and check the route ahead for clearances and hazards
Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.
-
23. What condition should the fifth wheel be in before you back under a trailer?
Show answer
Answer C: Jaws open, plate greased, and the fifth wheel tilted down toward the rear
The jaws have to be open to take the kingpin, the plate must be lubricated to prevent hard steering, and the fifth wheel is tilted down at the rear so the trailer apron can ride up onto it.
-
24. Which shock absorber condition is a defect?
Show answer
Answer C: A shock that is leaking, broken or disconnected at either mounting
A shock that has lost its fluid or its mounting no longer damps the suspension, so the wheel bounces and loses contact with the road.
-
25. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?
Show answer
Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it
Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.
-
26. When traction is poor, such as on packed snow, how should you speed up?
Show answer
Answer C: Very gradually, so the drive wheels do not spin
Gentle throttle keeps the drive wheels from breaking traction, because spinning wheels give up both grip and directional control.
-
27. What does gross vehicle weight mean, as opposed to gross vehicle weight rating?
Show answer
Answer B: The actual weight of the single vehicle plus everything it is carrying
Gross vehicle weight is what the vehicle actually weighs at that moment; the rating is the maximum the manufacturer allows it to weigh.
-
28. Federal rules say a commercial vehicle may not be driven unless what is true of its cargo?
Show answer
Answer B: It is properly distributed and adequately secured
The basic federal requirement is that the load be distributed properly and secured well enough that it cannot move, whatever the paperwork says.
-
29. Two tires in a dual set have noticeably different diameters. Why is that a problem?
Show answer
Answer C: The larger tire carries more than its share of the load and can be overloaded
The taller tire touches the road first and takes most of the weight, so it runs overloaded and hot while the smaller one does little work.
-
30. A strap runs from an anchor point on one side of the trailer, over the load, and down to an anchor point on the opposite side. How much of its working load limit counts toward the total required?
Show answer
Answer C: All of it
A tiedown that is anchored on one side, passes over or around the cargo and is anchored on the other side counts its full working load limit toward the aggregate figure.
-
31. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
32. You are stopped in traffic on a steep upgrade behind another truck. How much space should you leave in front?
Show answer
Answer A: Enough that you can pull away without rolling back into the vehicle behind you
Room ahead lets you get moving smoothly on a grade instead of having to hold the vehicle perfectly still or roll back toward the traffic behind.
-
33. What is the danger of letting engine speed climb past the top of the rated rpm range before you shift?
Show answer
Answer B: You can damage the engine, so the shift should be made before that point
Every engine has a rated operating range; running above it can cause serious engine damage, so the upshift belongs at the top of that range, not beyond it.
-
34. You are on a freeway and see brake lights come on in several vehicles far ahead of you. What should you do?
Show answer
Answer A: Ease off the accelerator and get ready to slow down
Brake lights well ahead are an early warning that traffic is slowing, and acting on them gives a heavy vehicle the room it needs.
-
35. When must a post-trip inspection be made?
Show answer
Answer D: At the end of each day the driver operates the vehicle
The post-trip inspection closes out each driving day so that anything found is recorded before the vehicle is handed to the next driver.
-
36. What should you look for on the electrical wiring in the engine compartment?
Show answer
Answer A: Worn, frayed or cracked insulation and loose or corroded connections
Damaged insulation can short a circuit against the frame or engine, which can kill a lamp you depend on or start a fire.
-
37. What is required of the hooks, rails, rings and anchor points that tiedowns attach to?
Show answer
Answer A: They must be part of the vehicle and strong enough for the load being secured
A tiedown is only as strong as what it is hooked to, so anchor points must be proper vehicle fittings rated for the job.
-
38. You have chosen 40 miles per hour as your safe speed for a downgrade. How should the brakes be used?
Show answer
Answer A: Brake firmly to about 35, release, and repeat at 40
Proper technique is firm application to about 5 miles per hour below the safe speed, then full release so the brakes cool before the next application.
-
39. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?
Show answer
Answer C: The drum is defective and must be repaired before the vehicle is driven
Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.
-
40. How soon must warning devices be placed after a commercial vehicle stops on the traveled part or the shoulder of a highway?
Show answer
Answer D: As soon as possible and in any case within 10 minutes
The hazard warning flashers go on immediately and the warning devices must be in place as soon as possible, never later than 10 minutes after stopping.
-
41. What tells a driver when to shift up in a vehicle with a manual transmission?
Show answer
Answer C: Engine speed in rpm together with road speed
Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.
-
42. On a tractor with a sliding fifth wheel, what does moving the fifth wheel forward do?
Show answer
Answer A: Puts more of the trailer weight onto the steering axle
Moving the coupling point forward transfers weight from the drive axles to the steering axle, which is how a driver corrects a drive axle that is over the limit.
-
43. After coupling, where should the fifth wheel release handle be?
Show answer
Answer A: In the locked position with the safety latch in place
The handle must be pushed in and latched, because a handle left out means the jaws can open and release the trailer while you are driving.
-
44. Where should a driver expect fog to form first?
Show answer
Answer D: In low ground, near water and in valleys
Cool moist air settles in low places, so fog patches appear in hollows, river valleys and near lakes before they appear anywhere else.
-
45. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
46. You are hauling a load of steel plate that is well within every weight limit but is stacked five feet high on a flatbed. What is the main concern?
Show answer
Answer A: The center of gravity is high, so the rig will roll more easily in a curve
Legal weight does not make a load safe; height raises the center of gravity and it is height, not weight alone, that decides how readily the vehicle rolls over.
-
47. On a one way street or a divided highway, where are the warning devices placed?
Show answer
Answer B: About 10 feet, 100 feet and 200 feet back toward the approaching traffic
When traffic can only come from one side, all three devices are spread out behind the vehicle to give approaching drivers a longer warning.
-
48. What is the main purpose of a retarder fitted to a heavy vehicle?
Show answer
Answer B: To help slow the vehicle and reduce the need to use the service brakes
Exhaust, engine, hydraulic and electric retarders all slow the vehicle so the brakes stay cool and wear less, especially on grades.
-
49. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?
Show answer
Answer C: Move weight off the drive axles and onto the trailer axles
Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.
-
50. What are you looking for when you check the drive belts in the engine compartment?
Show answer
Answer C: That each belt is snug and free of cracks, frays or heavy wear
A loose or cracked belt can break and stop the fan, the water pump or the alternator, which leads quickly to overheating or a dead electrical system.